Fiat 500 Radio Code – Find & Enter Your Code Fast

The Fiat 500 radio code is a four-digit anti-theft PIN that the factory-fitted head unit requires whenever its power supply is interrupted. From the revival of the Cinquecento in 2007 through the much-loved facelift that ran to 2019, every Nuova Fiat 500 came with a Continental- or Blaupunkt-manufactured unit that locks itself after a battery change or disconnection. The car will show CODE on the display and refuse to produce any sound until the correct code is entered — this guide tells you exactly how to find and use it.

Why Your Fiat 500 Radio Is Asking for a Code

The anti-theft lock activates whenever the head unit detects a loss of its permanent live feed. Typical triggers on a Fiat 500 include:

Replacing the 12 V battery — even a brief disconnection resets the unit
Battery draining completely flat, dropping below the minimum operating voltage
Removing the radio for dashboard, trim, or speaker work
A blown fuse on the radio's supply circuit
Purchasing a second-hand 500 where the original Fiat code card is no longer present

Fiat 500 Generations and Radio Fitments

The Nuova Fiat 500 (launched 2007) used a single core platform throughout its production life. The primary infotainment system is the Blue&Me, an integrated Bluetooth/hands-free/audio system developed jointly by Fiat and Microsoft. Continental and Blaupunkt supplied the hardware as OEM manufacturers.

Generation	Years	Radio unit(s)	Serial format
500 Mk1 (Nuova)	2007–2015	Blue&Me (Continental / Blaupunkt)	Serial on unit label; may carry BP prefix
500 Facelift	2015–2019	Blue&Me / OEM CD (Pioneer / Blaupunkt)	Serial on unit label

Some 500 Abarth and higher-spec trim variants were fitted with an upgraded OEM CD unit sourced from Pioneer or Blaupunkt rather than the standard Blue&Me. The code-retrieval process is the same regardless of which unit is fitted.

How to Find Your Fiat 500 Radio Serial Number

Unlike some Renault or Ford radios, the Fiat 500's Blue&Me unit does not have an on-screen diagnostic mode to display the serial number without removal. You will need to read the label on the unit itself.

Method 1 — Read the serial from the unit label

This is the standard method for all Fiat 500 models:

Use a flat plastic trim removal tool to carefully unclip the centre dashboard surround panel. The 500's retro-style dash is held by clips — no screws — so gentle, even pressure around the perimeter is sufficient.
With the surround removed, the head unit is accessible. Use a pair of DIN removal keys or the appropriate Fiat release tools to slide the unit out of its cage.
Look on the top, side, or rear of the unit casing for the serial number sticker. On Blue&Me units this is typically a 10–14 character alphanumeric string, sometimes prefixed with BP.
Note the serial number precisely, including any leading zeros or prefix letters. Visit our Fiat radio code page and enter the serial to receive your four-digit code.

Method 2 — Check the original Fiat documentation

All new Fiat 500s were supplied with a radio code card in the vehicle handbook wallet or glove box. If the car is used and this card is missing, the serial-number lookup above is the correct route. Some Fiat dealers recorded the code in the service history — worth checking if you have a full dealer service record.

How to Enter the Code on a Fiat 500

The Blue&Me and OEM CD units on the Fiat 500 use the preset buttons to enter the code. There is no touchscreen involved.

Turn the ignition to position II (accessories on, engine off). The display should show CODE or a series of dashes.
Use the numbered preset buttons (1–4) to set each digit. Each press of a button increments the digit displayed in that position by one (cycling 0 through 9).
On units with a controller knob, you can also turn the knob to scroll through digits, then press it to confirm each one.
Once all four digits are correct, press the OK or confirmation button (this may be labelled differently depending on trim level — some units use the Source or Mode button as the confirm key).
If entered correctly the display will clear and the radio will start operating immediately. The code does not need to be re-entered unless power is interrupted again.

Troubleshooting Common Error Messages

ERR / ERROR — The code you entered was incorrect. Wait for the temporary lockout period to expire (usually a short delay) before trying again with the correct code.
CODE (not clearing after entry) — You may have confirmed with the wrong button. Check that you pressed OK or the designated confirmation key — not just the last digit key.
--- (dashes, unresponsive) — The unit may be in a lockout state. Try leaving the ignition on for 30–60 minutes to allow the timer to reset.
No power / blank screen — Before assuming a code problem, check fuse F54 (or the radio fuse in the 500's fusebox under the bonnet or in the footwell). A blown fuse will prevent the unit from displaying anything at all.
SAFE — This is an older Fiat/Blaupunkt locked-state indicator. Enter the code as described above.

Frequently Asked Questions

Where is the radio code card for a Fiat 500?

Fiat placed a small laminated code card in the vehicle handbook wallet supplied with the car at purchase. Check inside the service booklet cover, the glove box, and any documents that came with the vehicle. On used Fiat 500s the card is often missing; in that case, retrieve the code from the unit's serial number using our lookup service.

Can I enter the Fiat 500 radio code without removing the unit?

Yes — you only need to remove the unit to find the serial number if the original code card is lost. Once you have the code (from the card or our lookup service), you enter it using the preset buttons with the unit in the dashboard. Removal is only required to read the serial from the label.

How many wrong attempts can I make before the Fiat 500 radio locks?

The Blue&Me and OEM CD units impose a temporary lockout after a number of incorrect attempts. The lockout is time-based — leave the ignition on for the required period and the unit will reset and allow further attempts. The lock is not permanent, so there is no risk of permanently disabling the unit through incorrect entries.

Is the Blue&Me code the same as the radio code?

The Blue&Me system integrates Bluetooth, USB music playback, and voice commands into the same unit as the radio. The anti-theft code unlocks the entire unit — including the Blue&Me functionality — not just the radio tuner. Once the code is accepted, all features become available simultaneously.

Do all Fiat 500 trim levels use the same code entry process?

The core entry process (preset buttons 1–4, confirm with OK or Mode) is consistent across Pop, Lounge, Sport, and Abarth variants. The physical layout of the buttons differs slightly between the standard Blue&Me and the upgraded OEM CD units, but the principle is identical. Refer to the label printed around your head unit's buttons if you are unsure which key acts as the confirmation.

Have your Fiat 500 serial number ready? Head to our brand lookup page and get your unlock code in seconds — no dealer, no waiting room.