Radio Locked After Jump Start

You have just managed to start your car after a flat battery or a roadside jump-start — and now the radio screen is showing CODE, SAFE or simply a blank display. This is completely normal and not a sign of any fault. The anti-theft lock activates automatically whenever the head unit loses power, even for a fraction of a second. Here is exactly what to do.

Why a Jump Start Triggers the Code Lock

Every factory-fitted stereo manufactured since the mid-1990s stores a small amount of information in volatile memory: specifically, a flag indicating that power has been continuously present. When battery voltage drops to zero — as it does during a full discharge or when jump leads are connected — that flag is cleared. On the next startup the radio detects that continuity of power was broken and enters its protective locked state.

This was designed to defeat radio thieves who would disconnect the unit's power to extract it. It works: a stolen unit is worthless without the code. The side effect is that legitimate owners face the same lock after any power interruption.

Step 1 — Wait for the SAFE Warm-Up Period

Some radios — particularly Volkswagen Group units (RCD 310, RCD 510, RNS 510) — display SAFE immediately after power is restored. This is not a code prompt. It means the unit is counting down an internal timer before it will accept the code.

• Leave the ignition on (engine running or accessory mode).
• Wait up to one hour; the screen will automatically change from SAFE to CODE 1 or a similar prompt.
• Do not attempt to enter the code while SAFE is displayed — it will not register.

Step 2 — Locate Your Code

Once the radio shows a code prompt, you need the correct four or five-digit number. Check these sources in order:

1. Original code card: usually in the glovebox, service book wallet or with the spare key.
2. Radio serial number display: many radios show their serial number on screen when you hold certain preset buttons (see brand-specific instructions via our brand guides).
3. Online retrieval: submit your serial number to MyRenaultRadioCode.com to get the code instantly without visiting a dealer.

Step 3 — Enter the Code

The entry method depends on the brand and model, but the general approach is the same across most units:

1. Use the numbered preset buttons (1–4 or 1–5) to select each digit. Each press increases the displayed digit by one.
2. Move to the next digit using the right-arrow, seek or a dedicated confirm button (varies by model).
3. Confirm the complete code by pressing the same confirm button one final time.

Brand / Radio	Entry method	Confirm button
Volkswagen RCD 310 / RCD 510	Buttons 1–4 cycle digits	Press and hold button 1 or seek
Ford 6000 CD	Buttons 1–4 cycle digits	Button 5 or asterisk (*)
Renault Update List / Tuner List	Buttons 1–4 cycle digits	Button 6
Peugeot RD4 / RD45	Buttons 1–4 cycle digits	Volume or separate confirm
Audi Concert / Symphony	Buttons 1–4 cycle digits	Mode or seek button

What If Too Many Wrong Codes Have Been Entered?

If the radio displays WAIT, 1000 or a countdown timer, a lockout has been triggered by previous incorrect attempts. Leave the radio powered on (engine not essential, but ignition on) and wait for the full countdown — typically 30 to 60 minutes on Volkswagen Group units, and longer on some Ford units. After the timer expires the radio will accept another attempt.

Important: Some Ford units impose a permanent lockout after ten incorrect lifetime attempts. Do not guess — retrieve the correct code from the serial number first.

Frequently Asked Questions

Will the lock happen every time I jump-start the car?

Yes, until the underlying battery issue is resolved. Once the battery is replaced or the alternator is repaired and the battery holds charge, power continuity is maintained and the radio will not re-lock.

My radio shows a blank screen after the jump start — is it broken?

Unlikely. A blank screen is usually the SAFE warm-up period on Volkswagen Group radios. Leave the ignition on for an hour and the display should return. If the screen remains blank after 90 minutes, there may be a fuse or wiring issue worth investigating.

Can I use the code I used last time?

Yes. The code is permanently fixed to the specific radio unit and does not change between power-loss events. Use the same code every time.

I lost my code card years ago — what now?

Retrieve the code online using the radio's serial number. Visit MyRenaultRadioCode.com, select your brand, and follow the instructions to display or read the serial. The code is usually delivered within minutes.